NTU and FNU are both units used to report water turbidity, but they are associated with different measurement conventions. NTU is commonly used with EPA Method 180.1, while FNU is associated with the nephelometric method in ISO 7027 using near-infrared light. Although ISO 7027-1:2016 recognizes numerical equivalence between NTU and FNU, measurement results should not automatically be treated as interchangeable without checking the instrument method and applicable standard.
Understanding these differences helps laboratories, water treatment operators, and equipment buyers select the right turbidity meter.
NTU stands for Nephelometric Turbidity Unit. FNU stands for Formazin Nephelometric Unit. Both describe turbidity based on light scattered by suspended particles in a water sample.
The main difference is the measurement method and optical configuration.
| Item | NTU | FNU |
|---|---|---|
| Full name | Nephelometric Turbidity Unit | Formazin Nephelometric Unit |
| Common reference | EPA Method 180.1 | ISO 7027 |
| Typical light source | Tungsten lamp | Near-infrared light, commonly 860 nm |
| Measurement principle | Nephelometric light scattering | Nephelometric light scattering |
| Typical application | Drinking water and general water testing | Water testing using ISO 7027 methods |
Important: The displayed unit alone does not prove that an instrument complies with a particular standard. Buyers should verify the light source, detector geometry, calibration procedure, and manufacturer's stated method.
ISO 7027 is an international standard for determining water turbidity. Its current quantitative method reference is ISO 7027-1:2016.
It describes two measurement approaches:
Nephelometry: Measures diffuse scattered radiation and is suitable for low-turbidity water. Results are commonly expressed in FNU.
Attenuation measurement: Measures the reduction in transmitted light and is more suitable for highly turbid water. Results are expressed in FAU.
For nephelometric measurement, ISO 7027 commonly uses light at approximately 860 nm and a detector positioned at 90° to the incident beam.
This near-infrared approach can reduce interference from water color compared with visible-light measurement in some applications.
EPA Method 180.1 is another widely referenced turbidity measurement method. It uses nephelometry and specifies a tungsten light source, with detector response in the visible-light range of 400–600 nm and a measurement angle centered around 90°.
The method's stated standard range is 0–40 NTU; higher values can be measured after appropriate sample dilution.
The practical differences include:
ISO 7027 commonly uses near-infrared light at 860 nm.
EPA Method 180.1 uses a tungsten lamp and visible-light detection.
Different optical configurations may respond differently to particle size, shape, and water color.
Therefore, if a project specification requires ISO 7027 or EPA Method 180.1, select an instrument explicitly designed and documented for that method rather than relying only on its displayed turbidity unit.
ISO 7027-1:2016 states that NTU and FNU have numerical equivalence for the nephelometric method. However, this does not mean that every NTU reading from every instrument will exactly match every FNU reading.
Differences in light wavelength, detector design, particle characteristics, and calibration can affect measurement results.
For reliable comparisons:
Use instruments following the same measurement method.
Calibrate with appropriate certified or traceable turbidity standards.
Keep sample handling and measurement conditions consistent.
Record the method and unit alongside test results.
Avoid comparing results from different optical methods without validation.
Before purchasing a turbidity analyzer, check the following:
Measurement standard: Does the instrument support the required ISO or EPA method?
Measurement range: Does the range cover the expected sample turbidity?
Resolution and accuracy: Are they suitable for the intended application?
Measurement configuration: Is it designed for portable, laboratory, or continuous online monitoring?
Calibration: Does it support the required calibration standards and procedures?
For field testing, the ERUN-SP5-B6 Portable Turbidity Meter offers a measurement range of 0–1000 NTU, resolution from 0.001 to 0.1 NTU, and selectable unit modes including NTU, FTU, and EBC.
Product information: https://www.erunwas.com/products-detail/id-399.html
The instrument's selectable units should not be interpreted as automatic certification for ISO 7027 or EPA Method 180.1. Confirm the required measurement method with the manufacturer before purchasing for a standards-specific application.
Q1: Is FNU the same as NTU?
They are numerically equivalent under the ISO 7027-1:2016 nephelometric method, but results from different measurement methods may not be directly interchangeable.
Q2: Which standard uses FNU?
FNU is commonly associated with the nephelometric method in ISO 7027, which uses near-infrared light.
Q3: What is the difference between ISO 7027 and EPA 180.1?
A key difference is the light source: ISO 7027 commonly uses 860 nm near-infrared light, while EPA Method 180.1 specifies a tungsten lamp with visible-light detection.
Q4: Can one turbidity meter display both NTU and FNU?
Some instruments offer selectable units. However, changing the displayed unit does not necessarily change the optical measurement method or establish compliance with another standard.
NTU and FNU are closely related turbidity units, but understanding the measurement method behind each result is essential. When selecting a turbidity meter, check the applicable standard, optical design, calibration requirements, and measurement range—not just the unit displayed on the screen.
ERUN provides portable and online water turbidity measurement instruments for different water testing applications. Contact ERUN to discuss your measurement requirements and suitable equipment configuration.